Steps to Program Sanyo Soundbar Universal Remote Control Codes

Do you need a universal Sanyo Soundbar Universal Remote Control Codes for your soundbar? Then this post is for you. A Sanyo universal soundbar remote control code is required if you want to sync your Sanyo soundbar with a universal remote control.

This post explains the code for you. Note that the first code may not work. All you have to do is choose the next code until you get the correct code for your electronic device.

Sanyo soundbar can be controlled with a universal remote control provided you have the correct programming manual and remote control codes specific to the soundtrack. Sanyo soundbar can be controlled or programmed to work with the CAB, SAT or Universal Remote.

Read More : Charter Spectrum Remote Control Codes

Following are the steps for programming your universal remote control on the Sanyo soundbar. The good thing is that you only need to go through this process once. Next time, use the remote control without repeating these steps.

Sanyo Soundbar Universal Remote Control Codes List

Here is the full list of Sanyo Soundbar Universal Remote Control Codes . See which one you like.

Sanyo Soundbar Universal Remote 3 Digit Code

These are Sanyo Soundbar Universal Remote Control Codes for universal remote

627	611
661	683
590	…..

Sanyo TV Universal Remote Codes 4 Digit

Here are the complete Sanyo Soundbar Universal Remote Control Codes

1166	1176
1156	0157

Sanyo Television Universal Remote Codes 5 Digit

If you are looking for any Soundbar Universal Remote Control Codes please have a look below

10159	30531
10154	20149
20039	30189
20047	21781
20081	10051
10250	20000
20035	20593
21593	……

How to program the Sanyo Soundbar Universal Remote without code method

Using the automatic search method, all universal remote control codes are scanned on the remote control. The codes are automatically scanned one by one to find the correct remote code that works with the remote to program the controller. Follow the instructions below:

Step – 1. Turn on the smart device as “television” you want to use with the universal remote control.

Step – 2. Turn on the remote control and touch the device button (TV, DVD, CBL and OK / SEL) for 3 seconds. The LED display light will indicate that the device is ready for programming.

Step – 3. Point the remote control towards the device and click “CH +” and “CH-” buttons. An On / Off signal will be displayed on the remote control.

Step 4. Press and hold the V+ or V- button until the device turns off.

Step – 5. Check the code by clicking the On / Off button. The device must be turned on. When turned ON, try changing the channel to make sure the remote has been programmed correctly.

Step – 6. Now tap on the “Device” button to save the code. The device LED will flashe twice to confirm the stored code.

How to program the Sanyo Soundbar Universal Remote using the manual method

Using the keycode method, we can easily program a universal remote control and it automatically identifies your equipment make and model.

Step – 1. To get started, “turn on the device.”

Step – 2.On the “Universal Sanyo Soundbar Remote Control,” press “TV” Button

Step – 3. Then, on the universal remote control, press and hold the “Setting” button until “Flash” displays (indicating that you are in “Training mode”).

Step – 4. At last, enter the “key code” that you have collected in the given programming manual (operating instructions).

Step – 5.After performing this, “point the remote towards the TV” then press and hold the “Power button”.

Step – 6 When the screen is turned off, you can release the “Power” button.

That’s all, your TV now works perfectly with a universal remote control. If your device doesn’t respond, repeat the same steps with other codes from the same section of the reference table.

How to program the Sanyo Soundbar Universal Remote with code search method

If you are unable to find a suitable key code for the device, you can program the universal remote control to the correct one while in search mode. This is a manual mode code method that forces the remote control to turn into search mode.

Step -1 First “activate device”

Step -2. Now hold down the “Setup” button

Step -3. Enter the code “9-9-1” (three digits)

Step -4. Now hold down the power button on the remote and press the channel upwards until the unit turns off the TV.

The method mentioned above may be time taking, but it is very important to find your key code. After completion of the above steps, your remote control will work for all functions/devices.

With the above three methods, we can easily program a universal remote control device on our Sanyo soundbar.